Joined in 2023 
82 
63 About this deal
I cut 1″ wide strips from these felt blankets and put them on either side of the bottoms of the boxes. They slide super easily now. After dry or wet sanding your primer, you may have to do some touch-up priming in spots where you sanded away the primer. No need to resand these spots, though, unless they’re substantial areas. Lastly, apply two or three coats of paint and your boxes are finished!
Step One: Cut the pieces needed for the sides and bottom of your boxes. See the section above about determining the sizes you need. Wire brads (I used 1/2″ brads to nail through 1/4″ plywood and 1″ brads to nail through 1/2″ plywood.)
Recommendations
Step Two: Use a 1″ hole saw bit to cut out the rounded edges of the slotted handle opening. Then use a jig saw to connect the holes, creating one opening. I recommend practicing on pieces of scrap wood before cutting into your box panels. Centering your hole saw and controlling the jig saw may take some practice to get it right. Tips for using a hole saw: When cutting holes with a hole saw drill bit, I recommend marking the center part of your hole first, then using a smaller drill bit to drill through that point. I chose to make my boxes 1″ more narrow than the shelving opening to give myself and my children wiggle room when returning each box to its space. I also made the height of the boxes 3/4″ shorter than the opening. I’m happy with how this sizing worked out for me. Determine Lumber Needed Storage & organisation Furniture Textiles Kitchenware & tableware Kitchens Lighting Decoration Rugs, mats & flooring Beds & mattresses Baby & children Smart home Bathroom products Laundry & cleaning Plants & plant pots Home electronics Home improvement Outdoor living Food & beverages Christmas Shop Shop by room
A standard courier service (DPD, TNT etc.) is usually used to deliver smaller items with a weight limit of 30kg and a maximum length of 1.5m per parcel. A delivery can comprise multiple parcels with no limit on total weight. Be very careful when tapping the brads into place, particularly into the 1/4″ plywood, because if they’re not perfectly centered and perpendicular, you’ll end up with nails poking out inside or outside of your box. Haste makes waste, or in this case, haste makes more work for yourself! After allowing one coat of the sealer to dry, lightly sand with a super fine sandpaper or 0000 grade steel wool to smooth out any roughness. Then add one or two additional coats of sealer to finish it off.
Success!
Step Five: Carefully remove the duct tape from the joints after the nails are in place. Peel slowly and toward the edge of your wood panels, not away from the edge, or you may pull apart bits of the plywood in the process. Having a lot of scrap wood left from previous projects is a good thing, it shows you’re working hard. However, to make the most of your lumber, you will need to keep them organized so that you can utilize them whenever there is a chance. Everything jumbled up together in a pile will not only make it hard for you to figure out what you have laying around in your workshop, but may also damage your wood. Thus, it is quite important to have proper storage installed. We hope we have been able to help you decide or get an idea regarding what type of storage option you want and need. Our paper and media boxes are sure to make this easy. And if you’re looking to organize the desk, we’ve got some great desk organizers and mini chest drawers. That way, you get complete control over your pens, scissors and associated items. And if you prefer to keep these things out of sight, use inserts with compartments for your desk drawers. Make room in the living room
I chose thermally modified poplar for this bench. Normally, poplar would be a poor choice for an outdoor project, but thermal modification changes the rules. Thermally modified wood (TMW) has essentially been cooked, removing the organic compounds. The chemical-free process makes wood more stable and resistant to decay and insects. The living room may not need the same storage solutions as the bedroom or the office. But it still has a way of attracting clutter and mess all the same. Extra sofa cushions, blankets, the kid’s toys, phone chargers, headphones, you name it. If you can carry it, it ends up in the living room, and more often than not on the floor.
Multifunctional Ply Boxes
Staining your Boxes: After sanding your boxes with 120 grit sandpaper, I recommend sanding one last time with 180 grit sandpaper before staining. You may choose to apply a wood conditioner to your wood before staining, which will help the wood accept the stain more evenly across its grain. Then apply your stain and allow it to rest for the period of time indicated on the label. Priming and Painting the Boxes: When painting your wooden boxes, you should apply a single coat of primer and allow the primer to dry completely. Next, lightly sand down the primer with a high grit sandpaper, such as 320 grit. Because I was using IKEA Billy bookcase units with about 14″ width openings, I was restricted to a box size that would fit inside each little cubby. Thoroughly sanding in this step is super important if you plan to stain rather than paint your boxes. If you don’t completely sand away scratch marks from the 80 grit sandpaper you used in step three, then those scratches will be highlighted after applying stain.
Nefab’s Sustainability Director Charles De Muizon about GreenCalc™ and its role in the Sustainable Supply Chain Transformation Many can probably relate to having a messy wardrobe. But decluttering it is easier than you might think. All you need is some good storage boxes. To make 11 boxes I used two full sheets of 1/4″ plywood plus about 1/2 of a sheet of 1/2″ plywood. (The 1/2″ sheet of plywood was leftover from this fold-away dollhouse project.) The planter is even simpler to build than the bench because the inner box has no top or bottom. Glue and screw the sides together, screw in the diagonal braces and then paint any visible surfaces. Add the slats using the same method as for the bench. Position the side cleats at a height suitable to the pot you’re setting in the planter. Don’t attach the platform slats. If the wood rots, they’ll be easier to replace. Planter Plans
When using the jig saw in this step, always err for a smaller hole rather than a larger hole. You can use sandpaper to make your jig saw cuts better match the hole saw cuts in step three. Be sure to remove any seeping wood glue before it dries! It is very difficult to sand away dried wood glue. And if you plan to stain your boxes, dried glue will repel stain and ruin your finish. Some people choose to wipe away wet wood glue with a damp rag (that’s me!), while others may use a chisel or blade to scrape it away as it begins to harden. But if you’re just painting the boxes, then a general smoothing down of the surface is good enough. After deciding on the height, width, and depth of your boxes, determine how much lumber you will need. Plywood is sold in 4’x8′ pieces, so I chose to have 1/4″ plywood sheets cut into strips at the hardware store. The bottom of my boxes were left unpainted, because I didn’t want paint scraping against shelves as the boxes are slid in and out. I had considered waxing the bottoms of the boxes so they’d slide more easily, but in the end I decided to use felt pads instead.
Great Deal 
New Comment